Adhesive strength of anti-friction polymer coatings with a cold-cured matrix
https://doi.org/10.46973/0201-727X_2025_3_190
Abstract
The creation of economical and durable coatings based on fluorine-containing compounds is one of the most important tasks in modern science. However, the high cost of fluoroplastic, which is a key component, has led to a constant search for ways to reduce the cost of producing these coatings without compromising their performance. The key idea is to create a multi-layer coating where each layer has a specific function. The matrix binder is a three-component system consisting of rubber, powdered copper, and molybdenum disulfide. The adhesion strength of the composite coating applied to a steel substrate was studied by peeling the samples at an angle of 180 degrees.
About the Authors
I. V. Bolshikh
Rostov State Transport University (RSTU)
Russian Federation
Russian Federation
Bolshikh Ivan Valerievich, Chair “Traction Rolling Stock”, Candidate of Engineering Sciences, Associate Professor
E. P. Bolshikh
Rostov State Transport University (RSTU)
Russian Federation
Russian Federation
Bolshikh Elizaveta Pavlovna, Chair “Theoretical Mechanics”, Junior Research Assistant
E. D. Anikina
Rostov State Transport University (RSTU)
Russian Federation
Russian Federation
Anikina Elena Dmitrievna, Chair “Theoretical Mechanics”, Postgraduate Student
Ya. K. Sklifus
Rostov State Transport University (RSTU)
Russian Federation
Russian Federation
Sklifus Yaroslav Konstantinovich, Chair “Traction Rolling Stock”, Candidate of Engineering Sciences, Associate Professor
References
1. Innovative technologies for increasing wear resistance of heavily loaded tribosystems by forming the structure and properties of their surface layer / V. I. Kolesnikov, I. V. Kolesnikov, D. S. Manturov, A. I. Voropaev // Science-intensive technologies in mechanical engineering. – 2024. – No. 8 (158). – P. 3–11. – DOI 10.30987/2223-4608-2024-3-11.
2. Sidashov, A. V. Study of fluoroplastic-containing nanostructured coating on the steel surface / A. V. Sidashov, M. V. Boyko, A. T. Kozakov // Trudy Rostovskogo Gosudarstvennogo Universiteta Putej Soobshcheniya. – 2020. – No. 4 (53). – P. 96–101. – ISSN 1818-5509.
3. Belyak, O. A. Predicting the Mechanical Properties of Antifriction Composite Materials / O. A. Belyak, T. V. Suvorova // Mechanics of Composite Materials. – 2021. – Vol. 57, No. 5. – P. 647–656. – DOI 10.1007/s11029-021-09986-7.
4. Improvement of tribological parameters of lubricants by introducing an inorganic polymer additive / I. V. Kolesnikov, M. A. Savenkova, A. P. Sychev [et al.] // Bulletin of Mechanical Engineering. – 2021. – No. 1. – P. 64–66. – DOI 10.36652/0042-4633-2021-1-64-67.
5. Savenkova, M. A. Effective polymer phosphomolybdate additive for lubricants / M. A. Savenkova, S. A. Volyanik, A. P. Sychev [et al.] // Vestnik Rostovskogo Gosudarstvennogo Universiteta Putej Soobshcheniya. – 2023. – No. 2 (90). – P. 172–179. – DOI 10.46973/0201-727X_2023_2_172.
6. Study of the adhesion strength of antifriction coatings based on phenylone / I. V. Bolshikh, A. M. Ananko, Ya. K. Sklifus, E. D. Anikina // Vestnik Rostovskogo Gosudarstvennogo Universiteta Putej Soobshcheniya. – 2024. – No. 4 (96). – P. 20–27. – DOI 10.46973/0201-727X_2024_4_20.
7. Kohanovsky, V. A. Adhesion of antifriction polymer coatings / V. A. Kohanovsky, I. V. Bolshikh, D. S. Manturov // Vestnik Rostovskogo Gosudarstvennogo Universiteta Putej Soobshcheniya. – 2017. – No. 4 (68). – P. 16–20. – ISSN 0201-727X.
Review
For citations:
Bolshikh I.V., Bolshikh E.P., Anikina E.D., Sklifus Ya.K. Adhesive strength of anti-friction polymer coatings with a cold-cured matrix. Vestnik Rostovskogo Gosudarstvennogo Universiteta Putej Soobshcheniya. 2025;(3):190-196. (In Russ.) https://doi.org/10.46973/0201-727X_2025_3_190
Views:
9
JATS XML
Email this article 