Experimental study of the influence of temperature on the physico-mechanical properties of a composite material
https://doi.org/10.46973/0201-727X_2024_1_186
Abstract
The influence of temperature on the physical and mechanical properties of the composite material has been studied. As the matrix of the polymer composite, epoxy-diane resin of the ED-20 brand was used using different types of fillers. The experimental data were obtained by instrumental indentation and thermal analysis. A relative change in indentation depth was used to estimate the creep rate of the material. Based on the obtained integral thermogravimetric curves of TG, a quantitative change in the mass of the sample during decomposition was determined, and based on differential thermogravimetric curves of DTG, the temperature range of destruction, the temperature of the beginning and end of decomposition were determined. It has been shown that the introduction of fillers into the polymer matrix has a significant effect not only on viscoelastic properties, but also on thermal stability as a result of structural transformations and changes in the mobility of molecules.
About the Authors
A. I. Azoyan
Rostov State Transport University (RSTU)
Russian Federation
Russian Federation
Anaid Iosipovna Azoyan, Junior Researcher
Chair «Theoretical Mechanics»
Rostov-on-Don
D. S. Manturov
Rostov State Transport University (RSTU)
Russian Federation
Russian Federation
Dmitriy Sergeevich Manturov, Head of Laboratory, Candidate of Engineering Sciences
Chair «Theoretical Mechanics»
Rostov-on-Don
D. N. Shishiyanu
Rostov State Transport University (RSTU)
Russian Federation
Russian Federation
Dariya Nikolayevna Shishiyanu, Candidate of Engineering Sciences, Associate Professor
Chair «Chemistry»
Rostov-on-Don
S. A. Danilchenko
Rostov State Transport University (RSTU); Southern Federal University (SFU)
Russian Federation
Russian Federation
Sergey Aleksandrovich Danilchenko, Junior Researcher
Chair «Theoretical Mechanics»; Institute for Mathematics, Mechanics and
Computer Sciences named after I. I. Vorovich; Laboratory for Mechanics of Deformable Bodies and Constructions
Rostov-on-Don
References
1. Investigation of the structure of polymer composite material based on ED-20 resins and anodisperity of styrene copolymer and acrylic acids / D. M. Mordasov, P. S. Makeev, D. L. Polushkin [et al.] // Vestnik Tambov State Technical University. – 2019. – Vol. 25. – No. 1 – P. 136–141. – DOI: 10.17277/vestnik.2019.01.
2. Dispersed-filled polymer composites for technical and medical purposes : monograph / B. A. Lyukshin, S. V. Shilko, S. V. Panin [et al.]. – Novosibirsk : Siberian Branch of the RAS. – 2027. – 311 p. – ISBN 978-5-7692-1546-9.
3. Paluvai, N. R. Synthesis and modifications of epoxy resins and their composites : A review / N. R. Paluvai, S. Mohanty, S. K. Nayak // Polymer-Plastics Technology and Engineering. – 2014. – Vol. 53. – No 16. – P. 1723–1758.
4. Investigation of kinetics and mechanism of secondary structures` formation of modified epoxy resin / D. S. Manturov, P. G. Ivanochkin, A. I. Azojan [et al.] // Vestnik Rostovskogo Gosudarstvennogo Universiteta Putey Soobshcheniya. – 2022. – No. 4 (88). – P. 41–51. – DOI: 10.46973/0201–727X_2022_4_41.
5. Study of viscoelastic properties of composite materials on the basis of indentation method / V. I. Kolesnikov, O. A. Belyak, T. V. Suvorova [et al.] // Vestnik Rostovskogo Gosudarstvennogo Universiteta Putey Soobshcheniya. – 2023. – No. 4 (92). – Р. 25–33. – DOI: 10.46973/0201–727X_2023_4_25.
6. Chyasnavichyus, M. Probing of polymer surfaces in the viscoelastic regime / M. Chyasnavichyus, S. L. Young, V. V. Tsukruk // Langmuir. – 2014. – Vol. 30. – No. 35. – P. 10566–10582. – doi: 10.1021/la404925h (date of access: 01/18/2024).
7. Zhai, M. Viscoelastic modeling of nanoindentation experiments : A multicurve method / M. Zhai, G. B. McKenna // J. Polymer Sci. B. Polymer Phys. – 2014. – Vol. 52. – No. 9. – P. 633–639. – doi: 10.1002/polb.23470 (date of access: 01/18/2024).
8. Measurement of viscoelastic properties for polymers by nanoindentation / Y. Wang, L. Shang, P. Zhang [et al.] // Polymer Test. – 2020. – Vol. 83. – P. 106353. – doi: 10.1016/j.polymertesting.2020.106353 (date of access: 01/18/2024).
9. Stan, F. Analysis of viscoelastic behavior of polypropylene/carbon nanotube nanocomposites by instrumented indentation / F. Stan, A. M. Turcanu, C. Fetecau // Polymers. – 2020. – Vol. 12. – No. 11. – P. 2535. – doi: 10.3390/polym12112535 (date of access: 01/18/2024).
10. Parvini, C. H. Extracting viscoelastic material parameters using an atomic force microscope and static force spectroscopy / C. H. Parvini, M. A. S. R. Saadi, S. D. Solares // Beilstein J. Nanotechnology. – 2020. – Vol. 11. – P. 922–937. – doi: 10.3762/bjnano.11.77 (date of access: 01/18/2024).
11. An indentation study of the temperature-dependent properties of modified polyurethanes / E. V. Torskaya, A. A. Yakovenko, I. V. Shkaley [et al.] // Physical Mesomechanics. – 2023. – Vol. 26. – No. 3. – P. 29–38. – DOI: 10.55652/1683-805X_2023_26_3_29.
12. Studying epoxy resin reinforced with silica dioxide nanoparticles by microindentation / S. V. Smirnov, E. O. Smirnova, I. A. Veretennikova [et al.] // Diagnostics, Resource and Mechanics of Materials and Structures. – 2017. – No. 1. – P. 24–35. – DOI: 10.17804/2410-9908.2017.1.024-035.
13. An overview of microscale indentation fatigue : Composites, thin films, coatings, and ceramics / Md. M. Islam, S. I. Shakil, N. M. Shaheen [et al.] // Micron–2021. – Vol. 148. – No. 18 – 22 p. – DOI: 10.1016/j.micron.2021.103110.
14. Effect of hardeners on the mechanical properties of epoxy coatings based on ED-2 resin // S. V. Smirnov, I. A. Veretennikova, D. A. Konovalov [et al.] // Diagnostics, Resource and Mechanics of materials and structures. – 2023. – No. 1. – P. 6–16. – DOI: 10.17804/2410-9908.2023.1.006-016.
15. Studying the Mechanical Properties of Epoxy Adhesive Coatings by Instrumented Indentation / S. V. Smirnov, I. A. Veretennikova, E. O. Smirnova [et al.] // Mechanics, Resource and Diagnostics of Materials and Structures (MRDMS-2019). – 2019. – 22 p. – DOI: 10.1063/1.5135120.
16. Belyak, O. A. Predicting the Mechanical Properties of Antifriction Composite Materials / O. A. Belyak, T. V. Suvorova // Mechanics of Composite Materials. – 2021. – Vol. 57. – No. 5. – P. 647–656. – DOI: 10.1007/s11029-021-09986-7.
17. Menczel, J. D. Thermal Analysis of Polymers : Fundamentals and Applications / J. D. Mencze, R. B. Prime // John Wiley & Sons, Incorporated. – 2014. – 2009. – 698 p. – DOI: 10.1007/s10973-010-1071-7.
18. Studies of epoxy resin modified by nanoscale iron spinel / P. G. Ivanochkin, S. A. Danilchenko, D. S. Manturov [et al.] // Vestnik Rostovskogo Gosudarstvennogo Universiteta Putey Soobshcheniya. – 2022. – No. 3 (87). – Р. 6–17. – DOI: 10.46973/0201–727X_2022_3_6.
Review
For citations:
Azoyan A.I., Manturov D.S., Shishiyanu D.N., Danilchenko S.A. Experimental study of the influence of temperature on the physico-mechanical properties of a composite material. Vestnik Rostovskogo Gosudarstvennogo Universiteta Putej Soobshcheniya. 2024;(1):186-195. (In Russ.) https://doi.org/10.46973/0201-727X_2024_1_186
Views:
51
JATS XML
Email this article 